Ceci est une ancienne révision du document !
Carte PCMCIA SFR 3G+
Installation Paquet (jusqu'à Hardy Heron 8.10 inclus)
Ouvrir un Terminal, se connecter en "root" et taper:
wvdial
si vous n’avez pas de réponse, Il faut donc installer le parquet
apt-get install wvdial
Installation Carte PCMCIA
Le terminal déjà ouvert avec l'user root nous allons afficher un fichier log pour connaître le driver que la carte utilise.
tail -10 /var/log/messages
Mettre la carte PCMCIA dans son emplacement (port pcmcia sur les côtés). Nous voyons apparaître de nouvelles lignes:
Apr 20 15:57:10 test-laptop kernel: [16923.068000] pccard: CardBus card inserted into slot 0 Apr 20 15:57:11 test-laptop kernel: [16923.536000] Initializing Nozomi driver 2.1 (build date: Apr 15 2007 05:40:45) Apr 20 15:57:11 test-laptop kernel: [16923.540000] nozomi 0000:04:00.0: Card type is: 2048 Apr 20 15:57:11 test-laptop kernel: [16923.540000] PCI: Enabling device 0000:04:00.0 (0000 -> 0002) Apr 20 15:57:11 test-laptop kernel: [16923.540000] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19 Apr 20 15:57:11 test-laptop kernel: [16923.540000] nozomi 0000:04:00.0: Nozomi driver nozomi_tty Apr 20 15:57:11 test-laptop kernel: [16923.540000] nozomi 0000:04:00.0: Version of card: 3 Apr 20 15:57:11 test-laptop kernel: [16923.540000] nozomi 0000:04:00.0: Initialization OK!
Ici, nous voyons que notre système a installé le driver nozomi, il faudra donc mettre /dev/noz0 pour le nom du périphérique du modem
Configuration WVDIAL
Editer le fichier /etc/wvdial.conf, effacez tout le fichier et copier/coller la configuration suivante:
[Dialer SFR] Modem = /dev/noz0 Baud = 460800 FLOWCONTROL= NOFLOW Init1 = ATZ Init2 = AT&F&D2&C1S0=0 Init3 = AT+CGDCONT=1,”IP”,”websfr” Phone = *99***1# Username = vodafone Password = vodafone Ask Password = 0 Dial Command = ATD Stupid Mode = 1 Idle Seconds = 3000 Auto DNS = 1
Enregistrer et Quitter
Lancer la connexion
Dans un terminal en root, taper:
wvdial SFR
Résultat:
–> WvDial: Internet dialer version 1.54.0 –> Initializing modem. –> Sending: ATZ ATZ OK –> Sending: AT&F&D2&C1S0=0 AT&F&D2&C1S0=0 OK –> Sending: AT+CGDCONT=1,”IP”,”websfr” AT+CGDCONT=1,”IP”,”websfr” OK –> Modem initialized. –> Idle Seconds = 3000, disabling automatic reconnect. –> Sending: ATD*99***1# –> Waiting for carrier. ATD*99***1# CONNECT 57600 –> Carrier detected. Starting PPP immediately. –> Starting pppd at Tue Apr 3 16:52:00 2007 –> pid of pppd: 21251 –> Using interface ppp0 –> pppd: Phone –> pppd: Phone –> pppd: Phone –> pppd: Phone –> pppd: Phone –> pppd: Phone –> local IP address 10.162.132.126 –> pppd: Phone –> remote IP address 10.64.64.64 –> pppd: Phone –> primary DNS address 172.20.2.10 –> pppd: Phone –> secondary DNS address 172.20.2.39 –> pppd: Phone –> Script /etc/ppp/ip-up run successful –> Default route Ok.
La connexion est établie.
Si problème DNS
Pour tester, ouvrir un terminal en root
ping doc.ubuntu-fr.org
Vous n'avez pas de réponse, essayer
ping 213.95.41.13
Si vous avez une réponse, il est possible que le DNS se soit mal configuré, donc éditer le fichier /etc/resolv.conf et ajouter:
nameserver 80.118.192.100 nameserver 80.118.196.36
Il faut re tester le ping de doc.ubuntu-fr.org
ping doc.ubuntu-fr.org PING doc.ubuntu-fr.org (213.95.41.13) 56(84) bytes of data. 64 bytes from lisa.ubuntu-eu.org (213.95.41.13): icmp_seq=1 ttl=52 time=71.8 ms 64 bytes from lisa.ubuntu-eu.org (213.95.41.13): icmp_seq=2 ttl=52 time=71.9 ms 64 bytes from lisa.ubuntu-eu.org (213.95.41.13): icmp_seq=3 ttl=52 time=73.8 ms 64 bytes from lisa.ubuntu-eu.org (213.95.41.13): icmp_seq=4 ttl=52 time=70.5 ms
Maintenant vous pouvez surfer en 3G.
Contributeurs : winnie31