Différences
Ci-dessous, les différences entre deux révisions de la page.
| Prochaine révision | Révision précédente | ||
|
scanner_epson_dx_7450 [Le 08/06/2010, 13:18] Mysteroïd créée |
— (Version actuelle) | ||
|---|---|---|---|
| Ligne 1: | Ligne 1: | ||
| - | {{tag>Lucid matériel imprimante scanner epson}} | ||
| - | ---- | ||
| - | |||
| - | ====== Epson - Multifonctions Stylus DX 7450 - Configuration Scanner ====== | ||
| - | |||
| - | ===== Avant propos : ===== | ||
| - | |||
| - | L'imprimante-scanner doit être sous tension | ||
| - | |||
| - | ==== Installer les librairies supplémentaires et les outils de sane : ==== | ||
| - | |||
| - | sudo apt-get install libsane-extras sane-utils | ||
| - | |||
| - | ===== Détecter et installer son scanner : ===== | ||
| - | |||
| - | Il suffit de taper dans une console : | ||
| - | |||
| - | sane-find-scanner | ||
| - | |||
| - | Ca vous donne quelque chose comme ça | ||
| - | # sane-find-scanner will now attempt to detect your scanner. If the | ||
| - | # result is different from what you expected, first make sure your | ||
| - | # scanner is powered up and properly connected to your computer. | ||
| - | # No SCSI scanners found. If you expected something different, make sure that | ||
| - | # you have loaded a kernel SCSI driver for your SCSI adapter. | ||
| - | found USB scanner (vendor=0x04b8, product=0x0838) at libusb:001:002 | ||
| - | # Your USB scanner was (probably) detected. It may or may not be supported by | ||
| - | # SANE. Try scanimage -L and read the backend's manpage. | ||
| - | # Not checking for parallel port scanners. | ||
| - | # Most Scanners connected to the parallel port or other proprietary ports | ||
| - | # can't be detected by this program. | ||
| - | # You may want to run this program as root to find all devices. Once you | ||
| - | # found the scanner devices, be sure to adjust access permissions as | ||
| - | # necessary. | ||
| - | |||
| - | Repérez les codes **vendor=0x04b8, product=0x0838** à la ligne | ||
| - | found USB scanner (vendor=0x04b8, product=0x0838) at libusb:001:002 | ||
| - | Dans le cas où votre scanner serait différent il faudrait adapter le code produit "0x0838" | ||
| - | |||
| - | Ouvrez un terminal et tapez : | ||
| - | |||
| - | sudo gedit /etc/sane.d/epson.conf | ||
| - | |||
| - | Ajoutez en fin de fichier : | ||
| - | usb 0x4b8 0x082b | ||
| - | |||
| - | Voila, le scanner devrait répondre lorsque vous tapez : | ||
| - | |||
| - | scanimage -L | ||
| - | |||
| - | Il ne vous reste plus qu'à lancer xsane | ||
| - | |||
| - | **Si ça ne marche pas**, Vérifiez que le fichier /etc/sane.d/dll.conf. | ||
| - | Si epson est en commentaire (#epson) effacez le #. | ||
| - | |||
| - | Si vous avez un "epson2" non commenté alors revenez à l'étape d'édition de /etc/sane.d/epson.conf ci-dessus mais éditez à la place (de la même façon) "/etc/sane.d/epson2.conf" | ||